KNetworkConf"> ]> Sean Wheller In Words Techdoc Solutions

sean@inwords.co.za

Christoph Eckert

ce.at.christeck.de

2005 In Words Techdoc Solutions Christoph Eckert &FDLNotice; 2005-03-24 1.0 This manual explains how to install and use &knetworkconf;, a module for &kcontrolcenter; that enables management of Network Interfaces, Routing and DNS properties. KDE tdeadmin network ethernet The &kcontrolcenter; provides users with a single integrated interface from which to manage a wide variety of system and desktop settings and preferences. &kcontrolcenter; can be started by selecting TDE Menu&kcontrolcenter;. The &knetworkconf; package was developed to enable users to manage TCP/IP networking settings in the same way they manage other system settings from &kcontrolcenter;. Tasks enabled by &knetworkconf; provide users with a simple interface from which to perform the following tasks: Apply IP addresses to interfaces Apply netmasks to interfaces Start and stop interface activities Configure Routing Configure Host- and Domain Name Configure Resolving Manage known hosts Once installed a new module called Network Settings is displayed in the &kcontrolcenter;. To start the Network Settings (&knetworkconf;) module select &kcontrolcenter; Internet & Network Network Settings in the &kmenu;. &knetworkconf; in user mode It is important to understand that &knetworkconf; cannot install networking hardware. As such physical devices and their drivers must be properly installed and configured in order for &knetworkconf; to display the device and enable management of networking properties. In most cases drivers for networking hardware and other devices are installed and configured while installing &Linux;. If you add networking hardware after installation, you will have to define the drivers to be loaded by editing one of the following files depending on your kernel version: &Linux; Kernel 2.4 and lower /etc/modules.conf &Linux; Kernel 2.6 and higher /etc/modprobe.conf The Network Settings module is loaded when the Network Settings option is selected in the &kcontrolcenter; index. When started the Network Settings module attempts to automatically detect the platform running on the system. Detecting the platform When the platform is not a recognized you will be prompted to manually select the platform. Select a platform from the list that most closely corresponds to your distro and its release. Check the Don't ask again option to make this choice permanent. Next time Network Settings is started the system will automatically default to the selected platform option. To manage the system network settings you must enter administrator mode. Prior to this all options will be grayed, meaning you can only navigate the interface and view properties. Editing is disabled. To enter administrator mode click the Administrator Mode button located bottom left of the module. Enter your password when prompted. &knetworkconf; in administrator mode &knetworkconf; in administrator mode Once in administrator mode all the modules functionality is enable. Functionality is organized into three tabs: The Network Interfaces tab is used to manage the network communications devices installed on the system. All available networking devices are listed. From the Network Interfaces tab the following tasks can be accomplished: The &knetworkconf; interface For each network device the following properties can be viewed: Interface Shows the name of the network interfaces. For example, eth0, eth1, wlan0. IP Address Shows the currently assigned IP address. Protocol Shows the boot protocol. State Shows the current state (up or down). Comment Shows the (freely assignable) comment. The properties of listed network devices can be configured by selecting the required device from the list then clicking the Configure Interface... button to display the Configure Device dialog. Configuring a networking device Configuring a networking device By default only basic TCP/IP settings are available. Click the Advanced Settings button to expand the dialog to include advanced properties. Advanced device configuration Complete the dialog values are as follows: Automatic Select the Automatic radio button when the TCP/IP settings are obtained from a DHCP server or BOOTP server node. In automatic mode the TCP/IP settings for the system are configured when the system services are started. The DHCP or BOOTP server sends all the required TCP/IP information each time the system is started, there is no need to configure any other settings. Use the drop-list to select DHCP or BOOTP according to your system. Manual Select the Manual radio button when you do not use DHCP or BOOTP for TCP/IP configuration. In the IP address field enter the TCP/IP address of the host. In the Netmask field enter the subnetwork address. Activate when the computer starts When checked this option will cause the system to initialize this network interface while the system is booting. If you do not want the device initialized leave this option unchecked. Description Enter a descriptive name. Broadcast Enter the broadcast address used to communicate with all hosts on the subnetwork. The values entered in this dialog will be displayed as the properties of the device in the device list. Make certain that the IP-address entered is not already in use on the network. Entering an IP-address that is already on the network will result in a TCP/IP conflict. Use ping from &konsole; to check if the address you want to enter is in use or not. If you are not sure how to complete this dialog, consult your network administrator. Network devices may be enabled or disabled depending on system requirements. To enable a disabled network device select the device from the list then click Enable Interface. Network devices may be enabled or disabled depending on system requirements. To disable an enabled network device select the device from the list then click Disable Interface. The Routes tab enables management of the system routing configuration. Advanced device configuration Default Gateway This specifies the IP address of the host on the local subnetwork that provides the physical connection to remote networks, and is used by default when TCP/IP needs to communicate with computers on other subnetworks. Select a device from the drop list to edit the Default Gateway value. If your computer offers more than one network interface, select the interface connected to network on which the gateway computer resides. The Domain Name System tab enables management of the system DNS configuration. Advanced device configuration Host name The name by which the host will be known on the subnetwork. Domain name The network domain in which the host resides. Domain Name Servers A list of DNS servers in order of preference (see ). Static Hosts A list of known hosts on the subnetwork system (see ). A computer running DNS matches up a fully qualified domain with a proper IP address. This is necessary because computers only understand the IP addresses. When a computer requests http://www.somedomain.com the DNS resolves this name to an IP-address such as 123.45.678.90. The Domain Name Servers part of the Domain Name System tab enables easy management of the list. Server properties can be added, removed and edited. DNS records can be arranged in order of preference by selecting a record and promoting or demoting the record in the list using the Move Up or Move Down buttons as required. From the Domain Name Servers group click the Add... button. The Add New DNS Server dialog is displayed. Enter the IP-address of the DNS server then click Add. The record is added to the DNS list. From the Domain Name Servers group select a DNS record then click the Edit... button. The Edit Server dialog is displayed. Editing a DNS server record Modify the IP-address then click OK. The record is updated to the DNS list. The Static Hosts list describes a number of hostname-to-address mappings for the TCP/IP subsystem. It is mostly used at boot time, when no name servers are running. On small, closed network systems, it can be used instead of Domain Name Servers. By default, the Static Hosts list contains some records describing the 'localhost' and a handful of special records for hosts that support IPv6. This still-experimental version of IP is destined to replace version 4. Click the Add... button. The Add New Static Host dialog is displayed. Enter the IP-address of the known host then click Add.... The Add New Alias dialog is displayed. Enter the name of the known host then click the Add button. If the known host has multiple aliases click the Add button again and enter another alias. When finished click OK to update the Static Hosts list. Select a static host record from the list, then click the Edit... button. The Edit Static Host dialog is displayed. Perform any of the following tasks, then click OK to update the Static Hosts list. To change the IP-address, enter a new IP-address, then click OK. To add a new alias, click the Add... button. To change an alias value, select the alias record, then click Edit.... To remove an alias, select an alias record then click Remove. Changes made via the Network Settings module are not automatically applied to the system environment. To apply the changes made, start &konsole; and execute the following command. /etc/init.d/networking restart You need &kde; 3.x and QT 3.x installed to use knetwork-conf. knetwork-conf can be used with the following platforms: &kubuntu; Conectiva Debian Fedora Core FreeBSD Gentoo &Mandrake; PLD OpenNA &RedHat; &SuSE; knetwork-conf's home page is at http://knetworkconf.sourceforge.net where you at least can download source packages. When using the binary distributions (most often rpm packages), it is enough to have the &kde; and QT binaries installed. Installing binaries is recommended for less experienced users. Simply download the rpm packages. Install them from &konsole; using RPM as follows: rpm -i knetwork-conf-versionnumber.rpm Alternatively, use a graphical front end like kpackage or the installation tool of your distribution. In this case, it is not enough to have the binaries of QT and &kde; installed; you also need the development packages which include libraries and other stuff. Recommended for advanced users only. Otherwise, compiling &knetworkconf; is not difficult. The following commands should do it. ./configure --prefix=$(tde-config --prefix) make make install The command make install must be run as root. That should do it. Should you run into any problems, please let us know. In the first section of this chapter, you'll find some valuable information about networking basics. In the second, all configuration files on your disk which can be changed by &knetworkconf; will be discussed. This section cannot be a replacement for further lecture of IP-Networking. In this appendix, you'll only find the basic informations to get you started integrating your machine into a small (home) network. Currently, IP-networking is done using TCP/IP version 4 (IPv4). IPv5 has never been used much. IPv6 is expected to get spread in the near future. So, this manual is based on the currently most spread IPv4. One of the most important informations for setting up an interface is the IP-address which you have to assign to the interface. In foreign networks, ⪚ your office, you have to ask the network administrator to tell you a valid IP-address, or you can use DHCP if this is available. In any case, you are not allowed to simply choose any IP-address! If you want to set up a small (home) network of your own, you should use IP-addresses from a range which has especially reserved for this purpose to prevent IP-address-conflicts with the global (Internet) network. The addresses from the table shown below are not routed in the Internet, so it is save to use them as you like. Of course these machines can later be configured for Internet access by using a gateway machine. You can freely use the following addresses: Class Range A 10.0.0.0 to 10.255.255.255 B 172.16.0.0 to 172.31.0.0 C 192.168.0.0 to 192.168.255.0 For smaller networks, the most often used addresses are these in the range of 192.168.1.1 to 192.168.1.254. This is enough for networks up to over 250 computers. Furthermore, the netmask is most often set to 255.255.255.0, so that all of these machines are members of the same subnet. Some addresses are reserved for special things, ⪚ 0.0.0.0 and 127.0.0.1. The first one is the so called default route, the second the loopback address. The default route is needed by IP routing. The network 127.0.0.1 is reserved for the IP-traffic which works on the local machine only. Usually, the address 127.0.0.1 is assigned to a special device, the so called loopback interface, which works like a closed circle. A default gateway is a computer which connects two different networks. If you have configured a small network of your own, it is most likely that you want all (or some) of your machines to grant Internet access. But this is not possible directly, because these machines use local private IP-addresses, which are not routed in the Internet. The solution is a computer which translates between the two different networks. This computer uses at least two interfaces. One of them, maybe an Ethernet card, points to the local network, the other one, maybe an ISDN card, points to the Internet. In this case, both interfaces use different IP-addresses. This computer performs a so called network address translation (NAT, aka IP-forwarding). To enable a local machine the Internet access, you have only to tell them the default gateway, the local IP-address of the gateway-computer. In this section you'll find the configuration files which are touched by &knetworkconf; and where they reside in the file system of the different distributions. In this file, the list of name servers is stored. Platform Release number Location Conectiva 9.2 /etc/resolv.conf Debian 3.0 /etc/resolv.conf Fedora Core 1 /etc/resolv.conf FreeBSD 5 /etc/resolv.conf Gentoo 2005.0 /etc/resolv.conf &Mandrake; 9.2 /etc/resolv.conf PLD 2.0 /etc/resolv.conf OpenNA 1.0 /etc/resolv.conf &RedHat; 9.0 /etc/resolv.conf &SuSE; 9.0 /etc/resolv.conf This file is sometimes dynamically changed by DSL-connections, so do not wonder if the file doesn't contain what you have put there when a DSL connection is established. In this file, the list of known hosts is stored. Distribution Releasenumber Location Conectiva 9.0 /etc/hosts Debian 3.0 /etc/hosts Fedora Core 1 /etc/hosts FreeBSD 5 /etc/hosts Gentoo   /etc/hosts &Mandrake; 9.2 /etc/hosts PLD 2.0 /etc/hosts OpenNA 1 /etc/hosts &RedHat; 9.0 /etc/hosts &SuSE; 9.0 /etc/hosts On &SuSE; it is known that this file gets occasionally resorted by the script SuSEconfig. So do not wonder if you do not find in a state you have expected. Thanks to all who have worked on &kappname;: Juan Luis Baptiste juan.baptiste@kdemail.net David Sansome me@davidsansome.com Carlos Garnacho garnacho@tuxerver.net Simon Edwards simon@simonzone.com Pedro Jurado Maquedo pjmelenas@biwemail.com Florian Fernandez florian.fernandez2@wanadoo.fr Unai Garro Unai.Garro@ee.ed.ac.uk Christoph Eckert mchristoph.eckert@t-online.de Jaime Torres jtorres@telecorp.net All the others which I have forgotten to list here - you know who you are you@foo.tld Christoph Eckert: mchristoph.eckert@t-online.de Sean Wheller: sean@inwords.co.za The Copyright on &kappname;, at least for the years 2003 and 2004, is owned by Juan Luis Baptiste: (juan.baptiste@kdemail.net). &underFDL; &underGPL;